|
 |
Subscribe to the DecoDreams monthly E-Zine to learn new ideas for your
home decorating needs.
>> more
|
|
Click
for Financing
 |
 |
| HOME
> Technical Information > Measuring
> Sheer Shades |
|
How to Measure for Sheer Shades
Measuring Guidelines
Important:
- Precise width and length measurements are critical. Fabric
width cannot be altered after the shading is fabricated.
- Please use a metal tape measure for accuracy from home to
factory.
-
The headrail must be installed perfectly
level and installed evenly to ensure smooth operation. On
an Inside Mount, it is recommended that you check to see that
the mounting surface is level and consistent. If your window
needs to be leveled, this should be done before measuring.
-
NOTE: All measurements should come from
measuring the window. If you measure your existing blinds,
the measurements will be incorrect.
Length Considerations:
| The manufacturer will fabricate your window
shading to the exact length ordered, when the vanes are in
the open (or view-through) position. When the vanes are rotated
to the closed position, the shading will become 3/8"
longer. |
| When closed on an inside mount, a slight puckering
can occur on the lower most sheer section because of contact
with the sill. To compensate, slightly raise the shading until
the rail begins to lift off the window sill. |
| If preferred, shades can be ordered 3/8"
less than the window opening's measured length. In this case,
the bottom rail will be positioned 3/8" above the sill
when the vanes are in the open position. (See diagram below).
Rotating the vanes closed will cause the bottom rail to touch
the window sill, closing any space. |
Measuring Instructions
Inside Mount:
-
Measure across the width of your window opening
in three different places - top, middle and bottom. Measurements
should be taken within the window jamb. Provide the smallest
of the three measurements. Be exact. The manufacturer will
make the necessary deductions to fit the window opening.
-
Measure the length of the window opening
from the underside of the soffit to the surface of the window
sill in two places - use the smallest of these two measurements.
Outside Mount:
Side Mount:
Shading Specifications
Width and Length Dimensions:
| Minimum Width: 12" |
Maximum Width: 112" |
| Minimum Length: 12" |
Maximum Length: 96" |
Finished Dimensions:
| The manufacturer makes deductions to the width
of the Window Shading depending on the selected mounting type.
For all mounting types, fabric will measure exactly the length
ordered when the vanes are in the open or "view-through"
position. |
Inside Mount:
Headrail will measure order width less:
3/16"
Fabric will measure ordered width less:
1 1/8" |
Side (End) Mount:
Headrail will measure order width less:
11/16"
Fabric will measure ordered width less:
1 5/8" |
Outside Mount:
Headrail will measure order width plus:
3/16"
Fabric will measure ordered width less:
3/4" |
Exact End to End Mount:
Headrail will measure ordered width
Fabric will measure ordered width less:
15/16" |
Width and Length Measurements may vary +/-
1/8"
Headrail measurement includes end caps. |
Note on Specifications:
Once ordered and manufactured, the width of the fabric cannot
be altered. Due to variations in fabric weave and environmental
conditions, the finished dimensions for both width and length
may vary, plus or minus 1/8", from your order measurements. |
Mounting Information:
Inside Mount:
Minimum depth for flush inside mount: 3 1/8" |
Shallow Mount:
Minimum depth required for mounting: 3/4" |
Side Mount:
Minimum depth for side mount: 1 1/4"
Maximum shading width for side mount: 48" |
Outside Mount:
Minimum surface area required for mounting: 3/4" |
Ordering and Hardware
Ordering Information:
- These shades are precision, hand crafted products. Once fabricated,
they cannot be altered for either width or length.
- In addition to width, length, cord positioning and color,
you have the option of ordering custom cord lengths, hold down
brackets, extension brackets and headrail types. Please indicate
these or any other special instructions on your order form when
placing your order.
Hardware:
Headrail Options:
Shangri-La's Nirvana Headrail is offered in two different
styles: color matched aluminum or fabric wrapped. |
Hold Down Brackets:
Hold down brackets are made of a clear plastic, which fits
into drilled holes in the end cap of the bottom rail. Hold
downs are most generally used to secure the bottom of the
window shading to prevent swaying. |
Extension Brackets:
Extension or "L" brackets are available which can
be used to project the back of the shading 2 1/2" from
the mounting surface. |
Spacer Blocks:
Spacer blocks project the shading 3/8" from the mounting
surface. Use spacer blocks to obtain clearance when obstructions,
such as window cranks or door handles, obstruct the movement
of the shading. |
Cleaning and Care
| The soft delicate feel of the shading fabric
belies the durability of the material. This shade is made
from a sturdy, knitted polyester fabric which can be feather
dusted or vacuumed at a low setting. Spots or stains can be
lightly rubbed clean with a damp sponge and mild soap. To
avoid discoloration of the material, we recommend against
the use of chemical cleaners. The fabric may also be ultrasonically
cleaned. |
Protect Your Children
|
| HOME
> Technical Information > Measuring
> Sheer Shades |
|
|
We Accept:
 |
